KATV 55 Blue-Mag machine for core drilling with HEAVY-DUTY guide system and sensorDrilling capacity:Core bits up to: fi 55 mm and depth up to 110 mmTwist drills: fi 3 mm to fi 23 mmCountersinking: fi 10 - 40 mmThread cutting: 6 - 20 mmHolder: Morse taper MK2 and Weldon 19 mm holder (other chucks on offer)Lubrication with emulsion: Built-in, internal coolingWeight: 13.00 kgMotor power: 1,250 WSpeed: 100 - 450 rpmStroke: 170 mmPower supply: 230 V / 50 HzMagnetic holding force: 1250 kgMagnetic foot: 85 × 180 mmThanks to the HEAVY-DUTY guide tape system, a drilling depth of 110 mm can be easily achieved.The machine is delivered standard with a 55 mm drilling depth chuck.If you need a drilling depth of up to 110 mm, we can offer very long holders or two-part ejector pins for core bits.SPECIAL ADVANTAGES:New HEAVY-DUTY system - advantages compared to machines with classic dove-tail guide.Up to 10 times greater stabilityExtremely small guide tolerances due to round guidesThe guide block does not have direct contact with the machine housing, but is exclusively guided by a high-precision and stable round rail system. Less friction and wear due to this Lower maintenance costs and greater reliabilityThis brings you:Longer drill bit lifeFewer drill bit breakagesMore precise drilling tolerancesBetter surface finish of drilled holesDrilling depth up to 110 mm is possible even with small drill machines.NEW MAG-TEC SENSOR:The sensor detects how well the magnet holds the machine to the surface.- it is directly connected to the motor.- if the sensor lights up "RED", the surface is contaminated (rust, paint residues, debris), the material is thinner than 6 mm, or the feed rate during drilling is too high. Therefore, the machine is unstable. The motor does not start or shuts off.- if the sensor lights up "GREEN", the magnetic adhesion force is optimal and the machine is safe to use.

ROBUST FOR LARGE DRILL HOLES* Four speed levels for core drilling from Ø 12-100 mm* Thread cutting M4-M30* Solid drilling up to Ø 32 mm* Weldon 19/ Weldon 32 crown chuck* Two rotation directions for drilling and thread cutting* MK3 tool holder* Robust magnetic drill with a 1880 W motor* Suitable threading taps are available* Set in a case with safety chain and toolsTECHNICAL CHARACTERISTICS:* Core drills [mm] Ø 12-100 mm* Max. solid drilling fixG: 16 mm x 110 mm* Solid drilling MK3: 32×150 mm* Magnet dimensions [mm] 215 x 11 mm* Magnet power 17,600 N* Motor - connection power 1880 W* Weight 26 kgNumber of revolutions: idle / loaded1: 90 / 70 min-12: 185 / 145 min-13: 305 / 245 min-14: 605 / 485 min-1Delivered in a case with a core drill holder, safety chain, snap hook, and hex key.

ELMAG's COREMAG core drilling machines are new high-performance units in the core drilling sector.These new models are characterized by ergonomic operation and the most modern design, combined with the latest technical standards.Core drilling capacity in steel: 12-75 mmCore drilling depth: 50 mmSolid drilling in steel D x l: 30×200 mmChuck: Weldon 19Speed range: 120/180/320/440 rpmNumber of speed levels: 4Stroke: 170 mmMagnet power: 14,000 NMotor power: 1,600 WPower supply: 230 V / 50-60 HzDimensions LxWxH: 416x227x440 mmWeight: 20 kgstandard equipment:- safety belt- emulsion tank- handy tools- carrying case

ELMAG COREMAG crown drilling machines are new high-performance devices in the crown drilling sector.These new models are characterized by ergonomic control and state-of-the-art design combined with the latest technical standards.Crown drilling capacity in steel: 12-50 mmCrown drilling depth: 50 mmSolid drilling in steel D x L: 20×200 mmClamping: Weldon 19Speed range: 250/550 rpmSpeed levels: 2Stroke: 170 mmMagnet force: 14,000 NMotor power: 1,600 WPower supply: 230 V / 50-60 HzDimensions LxWxH: 405x227x406 mmWeight: 18 kgStandard equipment:- Safety belt- Emulsion tank- Handy tool- Transport case

ELMAG COREMAG core drilling machines are new high-performance machines in the core drilling sector.Characteristic of these new models are ergonomic controls and the most modern design combined with the latest technical standards.Core drilling capacity in steel: 12-35 mmDrilling depth: 50 mmSolid drilling in steel D x l: 18×140 mmChuck: Weldon 19Speed range: 550/750 rpmSpeed stages: 2Stroke: 140 mmMagnet power: 7,500 NMotor power: 1,050 WPower connection: 230 V / 50-60 HzDimensions LxWxH: 390x226x350 mmWeight: 15.5 kgStandard equipment:- Safety strap- Emulsion reservoir- Handy tool- Transport case

ELMAG core drilling machines - core drilling with COREMAG are the new high-performance machines in the core drilling sector.Characteristic of these new models are ergonomic handling and state-of-the-art design combined with the latest technical standards.Core drilling capacity in steel: 12-35 mmCore drilling depth: 50 mmSolid drilling in steel D x l: 18×140 mmClamping: Weldon 19Speed range: 650 rpmSpeed levels: 1Stroke: 140 mmMagnet power: 7,500 NMotor power: 1,050 WMains connection: 230 V / 50-60 HzDimensions LxWxH: 390x226x350 mmWeight: 14.5 kgStandard equipment:- safety strap- emulsion tank- handy tool- transport case

ELMAG core drilling machines - core drilling with COREMAG are the new high-performance machines in the core drilling sector.Characteristic of these new models are ergonomic handling and state-of-the-art design combined with the latest technical standards.Core drilling capacity in steel: 12-35 mmCore drilling depth: 50 mmSolid drilling in steel D x l: 18×140 mmClamping: Weldon 19Speed range: 650 rpmSpeed levels: 1Stroke: 140 mmMagnet power: 7,500 NMotor power: 1,050 WMains connection: 230 V / 50-60 HzDimensions LxWxH: 390x226x350 mmWeight: 14.5 kgStandard equipment:- safety strap- emulsion tank- handy tool- transport case

ELMAG COREMAG core drilling machines are new high-performance machines in the core drilling sector.Characteristic of these new models are ergonomic controls and the most modern design combined with the latest technical standards.Core drilling capacity in steel: 12-35 mmDrilling depth: 50 mmSolid drilling in steel D x l: 18×140 mmChuck: Weldon 19Speed range: 550/750 rpmSpeed stages: 2Stroke: 140 mmMagnet power: 7,500 NMotor power: 1,050 WPower connection: 230 V / 50-60 HzDimensions LxWxH: 390x226x350 mmWeight: 15.5 kgStandard equipment:- Safety strap- Emulsion reservoir- Handy tool- Transport case

ELMAG COREMAG crown drilling machines are new high-performance devices in the crown drilling sector.These new models are characterized by ergonomic control and state-of-the-art design combined with the latest technical standards.Crown drilling capacity in steel: 12-50 mmCrown drilling depth: 50 mmSolid drilling in steel D x L: 20×200 mmClamping: Weldon 19Speed range: 250/550 rpmSpeed levels: 2Stroke: 170 mmMagnet force: 14,000 NMotor power: 1,600 WPower supply: 230 V / 50-60 HzDimensions LxWxH: 405x227x406 mmWeight: 18 kgStandard equipment:- Safety belt- Emulsion tank- Handy tool- Transport case

ELMAG's COREMAG core drilling machines are new high-performance units in the core drilling sector.These new models are characterized by ergonomic operation and the most modern design, combined with the latest technical standards.Core drilling capacity in steel: 12-75 mmCore drilling depth: 50 mmSolid drilling in steel D x l: 30×200 mmChuck: Weldon 19Speed range: 120/180/320/440 rpmNumber of speed levels: 4Stroke: 170 mmMagnet power: 14,000 NMotor power: 1,600 WPower supply: 230 V / 50-60 HzDimensions LxWxH: 416x227x440 mmWeight: 20 kgstandard equipment:- safety belt- emulsion tank- handy tools- carrying case

ROBUST FOR LARGE DRILL HOLES* Four speed levels for core drilling from Ø 12-100 mm* Thread cutting M4-M30* Solid drilling up to Ø 32 mm* Weldon 19/ Weldon 32 crown chuck* Two rotation directions for drilling and thread cutting* MK3 tool holder* Robust magnetic drill with a 1880 W motor* Suitable threading taps are available* Set in a case with safety chain and toolsTECHNICAL CHARACTERISTICS:* Core drills [mm] Ø 12-100 mm* Max. solid drilling fixG: 16 mm x 110 mm* Solid drilling MK3: 32×150 mm* Magnet dimensions [mm] 215 x 11 mm* Magnet power 17,600 N* Motor - connection power 1880 W* Weight 26 kgNumber of revolutions: idle / loaded1: 90 / 70 min-12: 185 / 145 min-13: 305 / 245 min-14: 605 / 485 min-1Delivered in a case with a core drill holder, safety chain, snap hook, and hex key.

KATV 55 Blue-Mag machine for core drilling with HEAVY-DUTY guide system and sensorDrilling capacity:Core bits up to: fi 55 mm and depth up to 110 mmTwist drills: fi 3 mm to fi 23 mmCountersinking: fi 10 - 40 mmThread cutting: 6 - 20 mmHolder: Morse taper MK2 and Weldon 19 mm holder (other chucks on offer)Lubrication with emulsion: Built-in, internal coolingWeight: 13.00 kgMotor power: 1,250 WSpeed: 100 - 450 rpmStroke: 170 mmPower supply: 230 V / 50 HzMagnetic holding force: 1250 kgMagnetic foot: 85 × 180 mmThanks to the HEAVY-DUTY guide tape system, a drilling depth of 110 mm can be easily achieved.The machine is delivered standard with a 55 mm drilling depth chuck.If you need a drilling depth of up to 110 mm, we can offer very long holders or two-part ejector pins for core bits.SPECIAL ADVANTAGES:New HEAVY-DUTY system - advantages compared to machines with classic dove-tail guide.Up to 10 times greater stabilityExtremely small guide tolerances due to round guidesThe guide block does not have direct contact with the machine housing, but is exclusively guided by a high-precision and stable round rail system. Less friction and wear due to this Lower maintenance costs and greater reliabilityThis brings you:Longer drill bit lifeFewer drill bit breakagesMore precise drilling tolerancesBetter surface finish of drilled holesDrilling depth up to 110 mm is possible even with small drill machines.NEW MAG-TEC SENSOR:The sensor detects how well the magnet holds the machine to the surface.- it is directly connected to the motor.- if the sensor lights up "RED", the surface is contaminated (rust, paint residues, debris), the material is thinner than 6 mm, or the feed rate during drilling is too high. Therefore, the machine is unstable. The motor does not start or shuts off.- if the sensor lights up "GREEN", the magnetic adhesion force is optimal and the machine is safe to use.