KATV 100 Blue-Mag crown drilling machine with HEAVY-DUTY guide system and MAG-TEC sensorDrilling capacity:Core drills up to: Ø 100 mm and depth up to 220 mmTwist drills: Ø 3 mm to Ø 32 mmCountersinking: Ø 10 - 55 mmThread cutting: 6 - 32 mmHolder: Morse taper MK3 and Weldon holder 19 mm (other holders on offer)Lubrication with emulsion: Built-in, internal coolingWeight: 22.7 kgMotor power: 1,800 WRevolutions: 60 - 470 rpmTravel: 255 mmPower supply: 230 V /50 HzMagnetic holding force: 2050 kgMagnetic base: 85 × 180 mmThanks to the HEAVY-DUTY guide rail system, a drilling depth of 220 mm can be easily achieved.The machine is equipped as standard with a 55 mm depth clamp.If you require a drilling depth up to 110 mm, we can offer very long holders or two-part ejector pins for core drills.SPECIAL ADVANTAGES:New HEAVY-DUTY system - advantages compared to machines with conventional dovetail guide.Up to 10 times greater stabilityExtremely small guide tolerances due to round guidesThe guide block does not have direct contact with the machine housing, but is exclusively guided by a high precision and stable round rail system. This results in less friction and wear Lower maintenance costs and greater reliabilityThis brings you:Longer drill bit lifespanLess drill bit breakageMore accurate drilling tolerancesBetter surface finish of drilled holesDrilling depth of up to 110 mm is possible even with small drilling machines.NEW MAG-TEC SENSOR:The sensor detects how well the magnet holds the machine on the surface.- directly connected to the motor.- if the sensor shows "RED", the surface is contaminated (rust, paint remnants, debris), the material is less than 6 mm thick, or the feed speed during drilling is too high. Therefore, the machine is not stable. The motor will not start or it will shut down.- if the sensor shows "GREEN", the magnetic holding force is optimal and the machine is safe to use.

KATV 55 Blue-Mag machine for core drilling with HEAVY-DUTY guide system and sensorDrilling capacity:Core bits up to: fi 55 mm and depth up to 110 mmTwist drills: fi 3 mm to fi 23 mmCountersinking: fi 10 - 40 mmThread cutting: 6 - 20 mmHolder: Morse taper MK2 and Weldon 19 mm holder (other chucks on offer)Lubrication with emulsion: Built-in, internal coolingWeight: 13.00 kgMotor power: 1,250 WSpeed: 100 - 450 rpmStroke: 170 mmPower supply: 230 V / 50 HzMagnetic holding force: 1250 kgMagnetic foot: 85 × 180 mmThanks to the HEAVY-DUTY guide tape system, a drilling depth of 110 mm can be easily achieved.The machine is delivered standard with a 55 mm drilling depth chuck.If you need a drilling depth of up to 110 mm, we can offer very long holders or two-part ejector pins for core bits.SPECIAL ADVANTAGES:New HEAVY-DUTY system - advantages compared to machines with classic dove-tail guide.Up to 10 times greater stabilityExtremely small guide tolerances due to round guidesThe guide block does not have direct contact with the machine housing, but is exclusively guided by a high-precision and stable round rail system. Less friction and wear due to this Lower maintenance costs and greater reliabilityThis brings you:Longer drill bit lifeFewer drill bit breakagesMore precise drilling tolerancesBetter surface finish of drilled holesDrilling depth up to 110 mm is possible even with small drill machines.NEW MAG-TEC SENSOR:The sensor detects how well the magnet holds the machine to the surface.- it is directly connected to the motor.- if the sensor lights up "RED", the surface is contaminated (rust, paint residues, debris), the material is thinner than 6 mm, or the feed rate during drilling is too high. Therefore, the machine is unstable. The motor does not start or shuts off.- if the sensor lights up "GREEN", the magnetic adhesion force is optimal and the machine is safe to use.

ROBUST FOR LARGE DRILL HOLES* Four speed levels for core drilling from Ø 12-100 mm* Thread cutting M4-M30* Solid drilling up to Ø 32 mm* Weldon 19/ Weldon 32 crown chuck* Two rotation directions for drilling and thread cutting* MK3 tool holder* Robust magnetic drill with a 1880 W motor* Suitable threading taps are available* Set in a case with safety chain and toolsTECHNICAL CHARACTERISTICS:* Core drills [mm] Ø 12-100 mm* Max. solid drilling fixG: 16 mm x 110 mm* Solid drilling MK3: 32×150 mm* Magnet dimensions [mm] 215 x 11 mm* Magnet power 17,600 N* Motor - connection power 1880 W* Weight 26 kgNumber of revolutions: idle / loaded1: 90 / 70 min-12: 185 / 145 min-13: 305 / 245 min-14: 605 / 485 min-1Delivered in a case with a core drill holder, safety chain, snap hook, and hex key.

ELMAG's COREMAG core drilling machines are new high-performance units in the core drilling sector.These new models are characterized by ergonomic operation and the most modern design, combined with the latest technical standards.Core drilling capacity in steel: 12-75 mmCore drilling depth: 50 mmSolid drilling in steel D x l: 30×200 mmChuck: Weldon 19Speed range: 120/180/320/440 rpmNumber of speed levels: 4Stroke: 170 mmMagnet power: 14,000 NMotor power: 1,600 WPower supply: 230 V / 50-60 HzDimensions LxWxH: 416x227x440 mmWeight: 20 kgstandard equipment:- safety belt- emulsion tank- handy tools- carrying case

ELMAG COREMAG crown drilling machines are new high-performance devices in the crown drilling sector.These new models are characterized by ergonomic control and state-of-the-art design combined with the latest technical standards.Crown drilling capacity in steel: 12-50 mmCrown drilling depth: 50 mmSolid drilling in steel D x L: 20×200 mmClamping: Weldon 19Speed range: 250/550 rpmSpeed levels: 2Stroke: 170 mmMagnet force: 14,000 NMotor power: 1,600 WPower supply: 230 V / 50-60 HzDimensions LxWxH: 405x227x406 mmWeight: 18 kgStandard equipment:- Safety belt- Emulsion tank- Handy tool- Transport case

ELMAG core drilling machines - core drilling with COREMAG are the new high-performance machines in the core drilling sector.Characteristic of these new models are ergonomic handling and state-of-the-art design combined with the latest technical standards.Core drilling capacity in steel: 12-35 mmCore drilling depth: 50 mmSolid drilling in steel D x l: 18×140 mmClamping: Weldon 19Speed range: 650 rpmSpeed levels: 1Stroke: 140 mmMagnet power: 7,500 NMotor power: 1,050 WMains connection: 230 V / 50-60 HzDimensions LxWxH: 390x226x350 mmWeight: 14.5 kgStandard equipment:- safety strap- emulsion tank- handy tool- transport case

ELMAG core drilling machines - core drilling with COREMAG are the new high-performance machines in the core drilling sector.Characteristic of these new models are ergonomic handling and state-of-the-art design combined with the latest technical standards.Core drilling capacity in steel: 12-35 mmCore drilling depth: 50 mmSolid drilling in steel D x l: 18×140 mmClamping: Weldon 19Speed range: 650 rpmSpeed levels: 1Stroke: 140 mmMagnet power: 7,500 NMotor power: 1,050 WMains connection: 230 V / 50-60 HzDimensions LxWxH: 390x226x350 mmWeight: 14.5 kgStandard equipment:- safety strap- emulsion tank- handy tool- transport case

ELMAG COREMAG crown drilling machines are new high-performance devices in the crown drilling sector.These new models are characterized by ergonomic control and state-of-the-art design combined with the latest technical standards.Crown drilling capacity in steel: 12-50 mmCrown drilling depth: 50 mmSolid drilling in steel D x L: 20×200 mmClamping: Weldon 19Speed range: 250/550 rpmSpeed levels: 2Stroke: 170 mmMagnet force: 14,000 NMotor power: 1,600 WPower supply: 230 V / 50-60 HzDimensions LxWxH: 405x227x406 mmWeight: 18 kgStandard equipment:- Safety belt- Emulsion tank- Handy tool- Transport case

ELMAG's COREMAG core drilling machines are new high-performance units in the core drilling sector.These new models are characterized by ergonomic operation and the most modern design, combined with the latest technical standards.Core drilling capacity in steel: 12-75 mmCore drilling depth: 50 mmSolid drilling in steel D x l: 30×200 mmChuck: Weldon 19Speed range: 120/180/320/440 rpmNumber of speed levels: 4Stroke: 170 mmMagnet power: 14,000 NMotor power: 1,600 WPower supply: 230 V / 50-60 HzDimensions LxWxH: 416x227x440 mmWeight: 20 kgstandard equipment:- safety belt- emulsion tank- handy tools- carrying case

ROBUST FOR LARGE DRILL HOLES* Four speed levels for core drilling from Ø 12-100 mm* Thread cutting M4-M30* Solid drilling up to Ø 32 mm* Weldon 19/ Weldon 32 crown chuck* Two rotation directions for drilling and thread cutting* MK3 tool holder* Robust magnetic drill with a 1880 W motor* Suitable threading taps are available* Set in a case with safety chain and toolsTECHNICAL CHARACTERISTICS:* Core drills [mm] Ø 12-100 mm* Max. solid drilling fixG: 16 mm x 110 mm* Solid drilling MK3: 32×150 mm* Magnet dimensions [mm] 215 x 11 mm* Magnet power 17,600 N* Motor - connection power 1880 W* Weight 26 kgNumber of revolutions: idle / loaded1: 90 / 70 min-12: 185 / 145 min-13: 305 / 245 min-14: 605 / 485 min-1Delivered in a case with a core drill holder, safety chain, snap hook, and hex key.

KATV 55 Blue-Mag machine for core drilling with HEAVY-DUTY guide system and sensorDrilling capacity:Core bits up to: fi 55 mm and depth up to 110 mmTwist drills: fi 3 mm to fi 23 mmCountersinking: fi 10 - 40 mmThread cutting: 6 - 20 mmHolder: Morse taper MK2 and Weldon 19 mm holder (other chucks on offer)Lubrication with emulsion: Built-in, internal coolingWeight: 13.00 kgMotor power: 1,250 WSpeed: 100 - 450 rpmStroke: 170 mmPower supply: 230 V / 50 HzMagnetic holding force: 1250 kgMagnetic foot: 85 × 180 mmThanks to the HEAVY-DUTY guide tape system, a drilling depth of 110 mm can be easily achieved.The machine is delivered standard with a 55 mm drilling depth chuck.If you need a drilling depth of up to 110 mm, we can offer very long holders or two-part ejector pins for core bits.SPECIAL ADVANTAGES:New HEAVY-DUTY system - advantages compared to machines with classic dove-tail guide.Up to 10 times greater stabilityExtremely small guide tolerances due to round guidesThe guide block does not have direct contact with the machine housing, but is exclusively guided by a high-precision and stable round rail system. Less friction and wear due to this Lower maintenance costs and greater reliabilityThis brings you:Longer drill bit lifeFewer drill bit breakagesMore precise drilling tolerancesBetter surface finish of drilled holesDrilling depth up to 110 mm is possible even with small drill machines.NEW MAG-TEC SENSOR:The sensor detects how well the magnet holds the machine to the surface.- it is directly connected to the motor.- if the sensor lights up "RED", the surface is contaminated (rust, paint residues, debris), the material is thinner than 6 mm, or the feed rate during drilling is too high. Therefore, the machine is unstable. The motor does not start or shuts off.- if the sensor lights up "GREEN", the magnetic adhesion force is optimal and the machine is safe to use.

KATV 100 Blue-Mag crown drilling machine with HEAVY-DUTY guide system and MAG-TEC sensorDrilling capacity:Core drills up to: Ø 100 mm and depth up to 220 mmTwist drills: Ø 3 mm to Ø 32 mmCountersinking: Ø 10 - 55 mmThread cutting: 6 - 32 mmHolder: Morse taper MK3 and Weldon holder 19 mm (other holders on offer)Lubrication with emulsion: Built-in, internal coolingWeight: 22.7 kgMotor power: 1,800 WRevolutions: 60 - 470 rpmTravel: 255 mmPower supply: 230 V /50 HzMagnetic holding force: 2050 kgMagnetic base: 85 × 180 mmThanks to the HEAVY-DUTY guide rail system, a drilling depth of 220 mm can be easily achieved.The machine is equipped as standard with a 55 mm depth clamp.If you require a drilling depth up to 110 mm, we can offer very long holders or two-part ejector pins for core drills.SPECIAL ADVANTAGES:New HEAVY-DUTY system - advantages compared to machines with conventional dovetail guide.Up to 10 times greater stabilityExtremely small guide tolerances due to round guidesThe guide block does not have direct contact with the machine housing, but is exclusively guided by a high precision and stable round rail system. This results in less friction and wear Lower maintenance costs and greater reliabilityThis brings you:Longer drill bit lifespanLess drill bit breakageMore accurate drilling tolerancesBetter surface finish of drilled holesDrilling depth of up to 110 mm is possible even with small drilling machines.NEW MAG-TEC SENSOR:The sensor detects how well the magnet holds the machine on the surface.- directly connected to the motor.- if the sensor shows "RED", the surface is contaminated (rust, paint remnants, debris), the material is less than 6 mm thick, or the feed speed during drilling is too high. Therefore, the machine is not stable. The motor will not start or it will shut down.- if the sensor shows "GREEN", the magnetic holding force is optimal and the machine is safe to use.